Ball Clevis

Model NO.: B C
HS Code: 73269090
Model NO.: B C
HS Code: 73269090
 Tension Clamp For Aluminium Conductor  
                  TECHNICAL SPECIFICATION
1.    SCOPE
      This specification covers the design and construction of Tension of Tension Clamps to be used for the termination of aluminium-conductors at terminal poles and section poles.      
       The Clamps are suitable for used in Tropical zone, with a maximum ambient temperature of approximately 40ºC and a mean annual temperature of approximately 28ºC with high humidity and heavy rainfall.
2.              STANDARD
this specification is make reference to and comply with the requirements of following standard:
BS 3288:1973    -    Insulator and Conductor fitting for
                    Overhead Power Lines
BS 729          -    Hot dip Galvanised
3.              ELECTRICAL SYSTEM
The Clamps will be designed for use on a 3 phase,3 wires, 33/22/11/6.6kv,50 Hz, primary distribution system with the star-point of the source-end transformer earthed through an Earthing Resistor.
4.              DESIGN AND CONSTRUCTION
The Clamps are manufactured from material which is not cause chemical corrosion when in constant contact with aluminium conductor. They are have a tensile strength that the breaking strength that are not less than the breaking strength of the conductors to be connected.
The Clamps are properly designed such that will not cause any unnecessary strain and abrasion on the surface of conductors.
5.              SIZE OF CLAMPS
The Clamps aredesigned to accommodate the following sizes of Aluminium conductors:
a.                  50mm2 Alu. Conductor
b.                  100 - 150mm2 Alu. Conductor
6.              MARKINGS
The Tension Clamps will be indelibly marked as Customer Requirment.
7.              INSPECTION AND TESTS
For evaluation purposes, we will supply the following items to our cusotmer
a.                  A  sample of the Tension Clamp complete with all accessories.
b.   A copy of the test report on tests conducted in accordance to BS 3288 and BS 729
 Tension Clamp For Aluminium Conductor  
                  TECHNICAL SPECIFICATION
1.    SCOPE
      This specification covers the design and construction of Tension of Tension Clamps to be used for the termination of aluminium-conductors at terminal poles and section poles.      
       The Clamps are suitable for used in Tropical zone, with a maximum ambient temperature of approximately 40ºC and a mean annual temperature of approximately 28ºC with high humidity and heavy rainfall.
2.              STANDARD
this specification is make reference to and comply with the requirements of following standard:
BS 3288:1973    -    Insulator and Conductor fitting for
                    Overhead Power Lines
BS 729          -    Hot dip Galvanised
3.              ELECTRICAL SYSTEM
The Clamps will be designed for use on a 3 phase,3 wires, 33/22/11/6.6kv,50 Hz, primary distribution system with the star-point of the source-end transformer earthed through an Earthing Resistor.
4.              DESIGN AND CONSTRUCTION
The Clamps are manufactured from material which is not cause chemical corrosion when in constant contact with aluminium conductor. They are have a tensile strength that the breaking strength that are not less than the breaking strength of the conductors to be connected.
The Clamps are properly designed such that will not cause any unnecessary strain and abrasion on the surface of conductors.
5.              SIZE OF CLAMPS
The Clamps aredesigned to accommodate the following sizes of Aluminium conductors:
a.                  50mm2 Alu. Conductor
b.                  100 - 150mm2 Alu. Conductor
6.              MARKINGS
The Tension Clamps will be indelibly marked as Customer Requirment.
7.              INSPECTION AND TESTS
For evaluation purposes, we will supply the following items to our cusotmer
a.                  A  sample of the Tension Clamp complete with all accessories.
b.   A copy of the test report on tests conducted in accordance to BS 3288 and BS 729

2.5MM Wire To Board Connectors

2.5MM Wire To Board Connectors.

Connectors can be classified into three basic types: line to line, line to board and board to board. These three types of connections are not entirely different. There are two reasons for this type of overlap. First of all, the design of the same connector only needs to be redefined after slightly changing the connection mode, that is to say, it becomes a new design scheme that can be applied to another type of connection mode; secondly, a cable can be installed with a line to line connector at one end and a line to board connector at the other end during assembly, for example, the appearance of class 5 I / O connector is the most common one See for example. If we avoid the fuzziness of this kind of connection, it will provide an effective basis for connector classification.

2.5MM Wire To Board Connectors

ShenZhen Antenk Electronics Co,Ltd , https://www.antenksocket.com