Free unlock Brush tutorial: red rice NOTE3 Netcom eat cotton candy

The words last shared their red rice NOTE3 full net high version with 360 N4S contrast

In the comments, some valued friends are very interested in red rice NOTE3 brush CM, I hope I can share the process, so there is this original. Below, I present the entire process in as much detail as possible.

1, because the brush system environment is different, I can not guarantee that the brush machine must be successful, and the tutorial may be a certain degree of danger, please carefully follow the operation, and carefully read the steps. If the mobile phone becomes bricked due to misoperation, or if you do not see the precautions, etc., I will not be responsible for turning the phone off.

2, I use the main card telecommunications, vice card Unicom, brushed third-party sometimes appear the following problems: use the main card telecommunication as the default dial-up, vice-card Unicom as the default Internet, open the mobile network main card will have no signal to call, brush Normal use after returning to MIUI, other combinations are temporarily unconditional tested. If there are similar requirements for use, please decide whether or not to use the brush.

3, red rice NOTE3 fingerprint recognition there are several hardware versions, the original CM13 now only supports FPC1020, like my golden network with ATMEL can not use the high, if the fingerprint unlocking requirements, do not brush. Do not know to enter the 6484 in the dialing interface to view.

4, Brush failure is not terrible, as long as you can enter the fastboot mode according to the program still can continue to brush, or brush back to the original MIUI.

First, download the various programs required

Line brush tool MiFlash download address

MIUI7.1.8.0 International Edition download address

Three other needed gadgets adb.zip, fastboot_edl.zip, TWRP_3.0.2-1_0512.zipPackaging Download

Poke me (extract code: d62a)

According to the preference choose other third party card to brush ROM spare, this time I selected the official version of CM13.

CM13-firmware download address

CM official brush package download address

Second, the computer system is normal (I use the WIN7 64-bit Ultimate Edition), the data line is normal, the desktop is best connected to the rear USB port, the battery power is guaranteed at more than 50%, a TF card, the CM13-firmware and The CM package (or third-party ROM of your choice) is copied to the root directory of the TF card and loaded into the phone.

Third, red rice NOTE3 backup personal data, close to find the phone, exit the millet account, special attention: the system needs to open the "developer mode" (enter the mobile phone settings on the phone item clicks 7 times MIUI version) and check the "OEM unlock mode ".

It is rather troublesome to apply for unlocking on the official website, and if it is later said that the unlocked machine does not provide a warranty, it will be tragic, so it has not gone and is not going to apply for unlocking.

First, install MiPhone20151028, the installation process will be prompted several times to verify the driver can be "always installed".

Second, unzip MIUI 7.1.8.0 International Edition, extract Unlocked_Bootloader.zip file emmc_appsboot.mbn replace the international version of the same name file within the brush package (in the MIUI unzip file image subdirectory).

Third, restart the phone to fastboot mode (press and hold "volume down" to restart or boot, shake and release the power button), connect the computer USB, install MIFLASH comes with driver. Now open the MiFlash brush tool and the phone's serial number (CPU ID) will be displayed at the device.

4. Decompress fastboot_edl.zip and double-click on edl in the fastboot_edl folder. Qualcomm 9008 driver will be installed. Refresh the MiFlash thread brush tool after installation. The COM10 will be displayed at the device (COM port numbers are different)

5. MiFlash line brush tool browses and selects the line brush package position of the unlocked file, and then clicks on the flashing machine, and waits for a few minutes to finish.

Six, decompress adb.zip, preferably on the disk partition root directory. Re-enter fastboot mode, connect the computer, the computer runs CMD command (or select the attachment → command prompt), open and use the CD command to enter the ADB folder

Then enter the following two instructions respectively to unlock the bootloader.

Enter fastboot oemdevice-info, and show OKEY and Finished.

Enter the fastboot oemunlock-go carriage return, showing OKEY and Finished.

The above diagram represents the successful unlocking of the bootloader, the machine will vibrate and enter the system ( if it fails, it will flash twice after the machine shakes and the MI boot screen will be blank. The reason for the failure is that the system is not turned on before the line brushing. The developer mode → OEM unlock mode is not checked )

First, open the developer mode after entering the system → check the usb debug.

Second, unzip TWRP_3.0.2-1_0512.zip, enter the fastboot mode again to connect to the computer, and click "Explicate third-party TWRPrecovery.bat (6.0 kernel)".

Third, according to the Chinese tips, any number of buttons.

Fourth, show the following figure to prove successful brushing, press any key will automatically exit.

First, after brushing into recovery you can flash machine, long press volume + power button to enter recovery, for the first time into the recovery, please click the figure, check no longer display, slide to confirm the modification, you can prevent the restart to restore the official rec.

Second, after entering recovery, select backup, backup partition (cache cust system data boot recovery partition can not backup, downgraded 5.1 from 6.0 only need to restore this backup and then brush into 5.1 rom).

Third, after the backup, choose to clear the default options, the first brush CM, you need to brush the bottom CM13-firmware.zip, otherwise there will be no fingerprint settings, security can not open, set flash back and other issues.

Fourth, after brushing CM13-firmware, wipe data, system, cache/dalvik, brush into the CM13 official ROM, restart after waiting patiently, CM13 comes with Chinese, boot memory usage is only 800M.

Knowing that CM will not need to introduce more, be the originator of MIUI, what cm does is transplant and develop, what MIUI does is beautify and upper application. This article mainly introduces the brushing process, and the CM casually intercepts several pictures to feel better. The obvious feeling of using a few days is that with more fluent power saving and the same usage habits, you can stick to half a day's time. The latest official CM13 has never encountered the phenomenon of FC. If you feel a bit tired of MIUI, you can try marshmallows, it is still very good.

Initially there are only 20 desktop apps.

Android 6.0.1 marshmallows, security patch updates.

After opening the developer options, you can enable the perfect ROOT authorization that comes with you.

Also supports multi-window mode, smooth use as split screen.

If the brush fails or you want to switch back to MIUI, you only need to press the text to go to the fifth step of the second part, select the official line brush brush to restart.

Red rice Note3 Netcom latest stable version of the line brush complete package download address

You value friends, look at me so hard to toss your own mobile phone, and use pieces of silver to submerge me!