24HR Electronic Timer socket with photocell.
â‘ Light intensity setting
â‘¡ Light intensity detection
â‘¢ Countdown Timer ON & OFF
â‘£ 4 MODES:
Set > Detected: When the light intensity detection value is less than the set value, switch ON or OFF.
Detected > Set: When the light intensity detection value is greater than the set value, switch ON or OFF
ON : Always ON
OFF : Always OFF
NOTED:
1. The light intensity displayed by this machine is not the standard light intensity value (Lux), only the relative light intensity value.
2. The light intensity value is affected by the placement position and direction. Please determine the position first and then set it according to the actual light intensity detected. If you change the position or change the orientation, you need to reset the light intensity setting value suitable for the new position.
3. This product has built-in rechargeable battery. If it is not connected to AC for a long time, you need to connect the power supply to charge until the LCD can display normally.
MANUAL OPERATION
1. Press [UP" or [DOWN" to set the LUX value.
2. Press the [SET" key to start setting, and the P1 settable items will be flashed.
3. Press [UP" or [DOWN" to adjust the value.
4. Press [SET" key again to exit setting or enter next setting for countdown timer.
5. Repeat the [SET" key to start setting, and the P2 & P3 settable items will be flashed.
6. Press the [FUN" key to switch the working state in the following:
Set > Detected -> Detected > Set -> ON -> OFF
Set > Detected: Automatically switches when the detected ambient light intensity is darker than the set value
Detected >Set: Automatically switch when the detected ambient light intensity is brighter than the set value
When the brightness meets the setting conditions, the countdown starts as below:
Note:when the countdown is ON, the detected value is not displayed.
When the brightness does not meet the setting conditions, the countdown stops and waits:
After the countdown ON is reduced to 0, the countdown OFF starts immediately and the power is OFF.
A. If the light intensity meets the set conditions, a new round of countdown will be started;
NOTE:
1. If the power is cut off while the countdown is running, the countdown will be terminated immediately and the relay output will be off. After the power is turned on again, a new round of brightness detection will start.
2. Modifying the brightness value in the countdown operation will not affect the current countdown operation. After the off time of the current countdown, the new brightness setting value will take effect.
3. In the countdown on operation, change the setting value of the countdown on, this countdown will still be timed according to the original setting value; the new setting value will take effect when the next countdown on starts.
Manual Control
Power Detection and Standby Mode
Photocell Timer, photocell timer socket, photocell sensor, photocell sensor socket, sensor plug, sensor switch socket, digital photocell timer, digital sensor timer NINGBO COWELL ELECTRONICS & TECHNOLOGY CO., LTD , https://www.cowellsocket.com
The "artificial sunlight" technology developed by Professor Zhou Zhuohui is to adjust the band combination of the three primary colors of red, blue and green by changing the voltage, so that the original OLED light color can be emitted as the sun is dim and cloudy. The state of the natural light color and color temperature, this invention was also published in the international period. Professor Zhou said that in general, the light-saving bulb contains mercury, the fluorescent tube will blink, and the LED illumination has glare and high heat. The "artificial solar color" OLED developed now is a cold light source, which meets environmental protection requirements. Made in plastic sheets, free to post like wallpaper, and create a variety of time, different climates, different latitudes of the sun, especially for areas where there is no long-term sunshine in Northern Europe, this light source is very useful.
Zhou Zhuohui said that the current cost of OLED is also close to the level of practicality. It is estimated that the cost per lumen will be about NT$1.4 in 2012 and 0.4 yuan per lumen in 2015, which will be fully popularized. At present, many large manufacturers negotiate cooperation, and the products will be listed soon after 2 years. 
After the countdown OFF is reduced to 0:
B. If the light intensity does not meet the set conditions, keep the power off and wait for the light to meet the conditions before turning on automatically.
4. In the countdown off operation, change the setting value of countdown off, this countdown will still be timed according to the original setting value; the new setting value will take effect when the next countdown off is started.
NOTE: the brightness setting value, countdown ON or countdown OFF, any one of which is equal to 0, cannot be switched ON or OFF automatically.
When ON or OFF is displayed, it means that the power supply remains ON or OFF, as shown in the figure below:
With AC power supply, the icon 
lights up and works normally.
When there is no AC power supply, the icon goes out, the brightness is not detected at this time, and the system enters the standby mode.
It is reported that Zhou Zhuohui, a professor of materials at the National Tsinghua University in Taiwan, has developed the world's first "artificial sunlight" OLED, which perfectly simulates sunlight. Professor Zhou said that the current cost of solar color OLED is close to the practical stage, and now there are many manufacturers willing to develop into products, which can be mass-produced in the next 2 years.